How to reconstitute peptides step by step
Work out how much water to add with a reconstitution calculator first. Then add bacteriostatic water slowly down the inside of the vial, swirl until clear and write the amount on the vial.
Reconstituting means adding water to the powder in your vial so you can draw it up as a liquid. If you’ve got a vial and a bottle of bacteriostatic water in front of you, these seven steps take about five minutes.
If your prescriber or pharmacy gave you instructions, follow those. This page covers the general method.
What you need before you start
- The peptide vial (the powder).
- Bacteriostatic water: sterile water with a small amount of preservative (benzyl alcohol), made for dissolving drugs for injection (Hospira label). Our bacteriostatic water guide explains how it differs from plain sterile water.
- Alcohol swabs.
- A syringe and needle for mixing. A 1 mL syringe moves up to 1 mL at a time. For more water, draw twice with the same one. Use it for mixing only, and throw it away once the vial is mixed.
- A new insulin syringe for each dose later.
- A sharps container for used needles.
Step 1: Choose how much water to add
Do this first. You can’t take water back out once it’s in.
Any amount can work. More water makes each dose a bigger volume, which is easier to read on a syringe. Less water keeps each dose small. The reconstitution calculator shows where your dose lands on your syringe for each common amount and marks the ones that sit on a printed line. For ready-made tables for 5, 10 and 15 mg vials, see how much water to add.
Step 2: Clean your hands and the vial tops
Wash your hands. Take the caps off both vials and wipe each rubber top with a fresh alcohol swab. Let them dry for a few seconds.
Step 3: Draw up the water
Draw the amount you chose from the bacteriostatic water vial. Tap out any big air bubbles, then push the plunger to your exact amount.
Step 4: Add the water slowly down the side of the vial
Push the needle through the rubber top of the peptide vial at an angle, so the tip points at the glass wall. Press the plunger slowly and let the water run down the glass. A jet straight onto the powder can make it foam.
If the plunger starts pushing back, the air inside the vial is being squashed. Stop, pull the plunger back a little so some of that air moves into the syringe, then keep adding the water slowly.
Step 5: Swirl gently and don’t shake
Swirl the vial gently, or roll it between your palms, until the powder has dissolved and the liquid is clear. Some powders take a few minutes. Shaking makes foam that’s hard to measure through.
If it stays cloudy or has specks after it should have dissolved, don’t use it. Ask whoever supplied it.
Step 6: Make a note of it
Make a note of the date you mixed it and how much water you added. Every dose from that vial depends on the water amount, so keep it somewhere you’ll find it.
Step 7: Store it somewhere cool
A mixed vial is usually kept in the fridge, or at least somewhere cool and out of direct light. If your product came with storage instructions, follow those.
Why the amount of water matters
The water you add sets the strength of the mix: the mg in the vial divided by the mL of water.
| Vial | Water added | Strength | 250 mcg is |
|---|---|---|---|
| 10 mg | 1 mL | 10 mg/mL | 2.5 units |
| 10 mg | 2 mL | 5 mg/mL | 5 units |
| 10 mg | 3 mL | 3.33 mg/mL | 7.5 units |
The vial and the dose are the same in every row. Only the mark on the syringe moves. So a dose given to you in units only makes sense if you know how much water went in. The FDA has reported people taking several times their intended dose of a mixed injectable after mixing up units, mL and mg (FDA alert).
Common mistakes
- Not noting the water. Without it you can’t work out a dose later.
- Spraying onto the powder. Aim at the glass wall.
- Shaking. Swirl or roll.
- Injecting with the mixing needle, or reusing an injection needle. The mixing syringe is for mixing only. Every dose gets a new insulin syringe. The CDC treats needles and syringes as single use (CDC).
- Using plain sterile water and keeping it. Sterile water without a preservative is made for single use. See the bacteriostatic water guide.
FAQ
How much water should I add? Any amount can work. Start from your dose: the reconstitution calculator shows which amount of water puts it on a clear line on your syringe. 1, 2 or 3 mL are common.
What water do I use? Bacteriostatic water. It has a preservative, so the vial can be drawn from more than once. Plain sterile water is for single use.
Does more water make my dose weaker? No. The vial holds the same amount of peptide whatever you add. More water only means each dose takes up more liquid, so you draw to a higher mark.
Why add the water down the side of the vial? A jet straight onto the powder can make it foam. Running it down the glass is gentler.
Should I shake it to mix it? No. Swirl it or roll it between your palms until it’s clear. Shaking makes foam that’s hard to measure through.
What if it’s cloudy or has bits in it? If it hasn’t cleared after a few minutes of swirling, don’t use it. Ask whoever supplied it.
Where do I keep it once it’s mixed? Usually in the fridge, or somewhere cool and out of direct light. Follow your product’s instructions if it has any.
Can I use the mixing needle to inject? No. Use it only to mix, then throw it away. Every dose gets its own new insulin syringe.
What do I need to remember after mixing? The date and how much water you added. You need the water amount to work out every dose from that vial.
I forgot how much water I added. Can I work it out? Not reliably from the vial. Don’t guess. Ask the pharmacist or prescriber who supplied it.
Sources
- Bacteriostatic Water for Injection, USP: prescribing information, Hospira (Pfizer), via DailyMed, US National Library of Medicine, Label revised August 2019.
- Preventing Unsafe Injection Practices, US Centers for Disease Control and Prevention.
- FDA alerts health care providers, compounders and patients of dosing errors associated with compounded injectable semaglutide products, US Food and Drug Administration, July 2024.