How much bacteriostatic water to add to 5, 10 and 15 mg vials

There is no single right amount. 1, 2 or 3 mL are common. Choose an amount that puts your dose on a line you can read and fits your syringe, then use that number every time you calculate.

How to choose

The water sets how much liquid each dose takes up, and so where it sits on your syringe. The amount of peptide in the vial stays the same.

If you were told how much water to add, use that. Otherwise, pick an amount that does two things:

  1. Puts your dose on a printed line. On a 1 mL syringe the lines are every 2 units. On 0.3 and 0.5 mL syringes they’re every unit.
  2. Keeps your dose at a readable size. Under about 2 units is hard to measure accurately.

The rule behind every table

strength (mg per mL) = mg in the vial ÷ mL of water
units = dose in mg ÷ strength × 100

On a U-100 insulin syringe, 100 units is 1 mL. 1 mg is 1,000 mcg.

5 mg vial

Water Strength 100 mcg 250 mcg 500 mcg 1 mg
1 mL 5 mg/mL 2 units 5 units 10 units 20 units
2 mL 2.5 mg/mL 4 units 10 units 20 units 40 units
3 mL 1.67 mg/mL 6 units 15 units 30 units 60 units

10 mg vial

Water Strength 100 mcg 250 mcg 500 mcg 1 mg
1 mL 10 mg/mL 1 unit 2.5 units 5 units 10 units
2 mL 5 mg/mL 2 units 5 units 10 units 20 units
3 mL 3.33 mg/mL 3 units 7.5 units 15 units 30 units

15 mg vial

Water Strength 100 mcg 250 mcg 500 mcg 1 mg
1 mL 15 mg/mL 0.67 units 1.67 units 3.33 units 6.67 units
2 mL 7.5 mg/mL 1.33 units 3.33 units 6.67 units 13.33 units
3 mL 5 mg/mL 2 units 5 units 10 units 20 units

Every number here comes from the same code as the calculator. The doses in the columns are examples to show the pattern. DoseClear doesn’t recommend doses.

Reading the tables

  • More water, bigger numbers. Doubling the water doubles the units for the same dose. That makes small doses easier to read, but large doses may no longer fit a small syringe.
  • Matching strengths give matching answers. 10 mg in 2 mL and 15 mg in 3 mL are both 5 mg/mL, so 250 mcg is 5 units in both.
  • Fractions mean “between the lines”. 2.5 or 3.33 units can’t be drawn exactly. Changing the water usually fixes that.

Why the number has to be written down

A dose in units needs the water amount beside it. 5 units is 250 mcg from a 10 mg vial mixed with 2 mL, but 500 mcg if the same vial was mixed with 1 mL. The FDA has reported people taking several times their intended dose of a mixed injectable after confusing units, mL and mg (FDA alert). Label the vial with the water you added, and check any dose in units against the mg you were told.

FAQ

Is 1, 2 or 3 mL best? The best amount is the one that puts your dose on a clear line. The calculator marks those for your vial and dose.

Does more water make my dose weaker? No. Your dose holds the same amount of peptide. It just takes up more liquid, so you draw to a higher mark.

What if my dose falls between two lines? Try a different amount of water, or a 0.5 mL syringe, where every small line is 1 unit.

Do I need to remember the amount? Yes. Every dose from that vial is worked out from it. Note it the day you mix.

0102030405060708090100Line the stopper up here: 10Needle endPlunger
5 mg mixed with 2 mL: a 250 mcg dose is 10 units, right on a numbered line.
0102030405060708090100Line the stopper up here: 2.5Needle endPlunger
10 mg mixed with 1 mL: the same 250 mcg is only 2.5 units, between two lines and hard to read.

Sources

  1. FDA alerts health care providers, compounders and patients of dosing errors associated with compounded injectable semaglutide products, US Food and Drug Administration, July 2024.
  2. Bacteriostatic Water for Injection, USP: prescribing information, Hospira (Pfizer), via DailyMed, US National Library of Medicine, Label revised August 2019.

How this page was made and checked: editorial policy.